Intermaher Shows the technological novelties of Mazak in his Catalan headquarters
15 November 2011
And is that it could not overlook the can see in action and in direct the novelties that the Japanese insignia Mazak showed in the last edition of the EMO, celebrated in Hannover. In general, from Intermaher show satisfied in spite of the times that run: “they Are difficult times and, taking into account all what this involves, give by good the results”, affirms Elio Estrany. Between these results, probably will be able to include “some interesting operations”, that as they always will have to expect to the finance: “we Are expecting to know the answer of the banks to close them”, declares Estrany.
As in other alike occasions, Intermaher had the collaboration of companies stood out as
The ‘fact in one' of Integrex
The range Integrex, and his consign ‘done in one', has increased the family with two novelties that Intermaher presented in his open house after the EMO. These two multitarea —Integrex j200 and Integrex i200S— combine the capacities of a centre/center of mechanised/mechanized and of a lathe, allowing finish complex pieces in an alone tie up. “They are many the advantages of the Integrex when it is necessary to mechanise/mechanize pieces of value that require several processes of mechanised/mechanized”, comments Elio Estrany, of which stands out: “Piece finished in the same machine; better term of delivery; it does not require cost of tooling for the centre/center; lower time of preparation that are increasingly decisive by the increasingly short series; better precision of the mechanised/mechanized and reliability of the process; less material inmovilizado between processes; lower dependency of the operario during the process of mechanised/mechanized, between many others”.
The Integrex i200S, with a futuristic design entirely renewed work of the Japanese designer Ken Okuyama, has of 2 dishes and an axis And of 250 millimetres/millimeters, voltea 658 millimetres/millimeters with a length of cut of 1.011 millimetres/millimeters and aúna in an alone machine to a lathe with two cabezales and to a centre/center of mechanised/mechanized of 5 axes. As it comments us Elio, “the series Integrex ‘i' allow more options as they are machine with double cabezal to mechanise/mechanize pieces with 2 phases of mechanised/mechanized of automatic form, inferior tower to improve the times of cycle, continuous movement of the twist of the cabezal for mechanised/mechanized with 5 continuous axes, etc. and has of more power in his accionamientos”.
Regarding the Integrex j200, Intermaher defines it like the ‘portal of entrance' to the teams multitarea, and presents it like this because “it has some very useful characteristics for the customer and a provision limited in regard to the series i200. Like consequence, his price is more adjusted and is a very valid solution for the one who precise something more than a lathe with motorised/motorized tools. His control Matrix Nexus allows to program the mechanised/mechanized to realise/realize on foot of machine, with his language type CAM Mazatrol, very appreciated by all his users”, explains the delegate in Catalonia of Intermaher. His maximum diameter of court and his maximum length of mechanised/mechanized are of 500 millimetres/millimeters, with an axis And of 200 millimetres/millimeters.
In addition to the teams Integrex, could see exposed and in operation a centre/center of turning of the series Smart of Mazak, the QTS 200M/1000 with a cabezal of tornear of 25 HP, a maximum diameter of cut of 360 millimetres/millimeters, a maximum length of mechanised/mechanized of 1.055 and tools to mill of 7,5 HP. Also it exhibited the centre/center of mechanised/mechanized Mazak, also of the series Smart, presented in the EMO: VCS 430 FZ ISO40 with table of 900 x 430 millimetres/millimeters. On them, Elio Estrany declares: “Mazak characterises/characterizes for offering the maximum provision is his distinct models. With the series Smart, has looked for adjust the specifications of machine to the most general needs of the market, always keeping a standard of quality very high. In the numerical control, has happened the same and has of a CNC simpler to use and, instead, faster, so much in the execution of the program as in the programming”.
More than 35 years in Catalonia
Intermaher, S.A. constituted in May of 1975, turning into exclusive representative of the Japanese mark Mazak in Spain, and in few years consolidated like leader in the Spanish market of import of machines of numerical control. Given his penetration in the market and the technological advance of his machines, the company with headquarters in Áraba opened his delegations in Barcelona and in Madrid, and endowed them of commercial technicians and service posventa. Elio Estrany explains us the path of the Catalan headquarters of the company: “From the year 1976, Intermaher has delegated in Catalonia. In the year 1982 opened his first delegation in the Passeig Maragall of Barcelona. Later, in the year 1988, moved to some installations but wide in the street Vilapiscina of Barcelona and in the year 2000, opened the current delegation in Montcada i Reixac where have space to be able to do events like this, classroom of training for the customers and an archive typical of scheme them installed in Catalonia to ensure an optimum attention to the customer with the Service Posventa.
In Catalan earths, the majority of the customers of Intermaher are related with the outsourcing “although we have several customers with own product that mechanise/mechanize his pieces”. And it adds: “it says that the machine-tool is the mother of all the machines and any manufacturer of textile machinery, machinery for the packaging, flexographic machines, for the feeding, automotion, etc. are potential customers of Intermaher”. In opinion of Elio Estrany, in general, the mecanizadores are conscious that invest in technology tip like which offers Mazak, in the long run reduces costs and improves the productivity: “At present, the main current problem is the insecurity with regard to the future and the financial crisis. We expect that all this improve in the next months and can go back to a more rational activity”, affirms.