Up to 15 represented from commercial Douma show their what's new in the 2010 K

battenfeld-cincinnati will present at the K 2010 numerous developments in their lines of pipe and profile extrusion, integrated within their new divisions for infrastructure and construction, respectively.

By the merger of both companies, the new emerging society comes not only reinforced by its extensive programme of supply, the largest in the market, has been further increased by the inclusion of new models and sizes of extrusion machines than before did not offer any of the two manufacturers, but that has been able to combine the most widely accepted technology in the market by both manufacturers in this start-up resulting.

The Division of infrastructure (pipe extrusion) will present, in addition to new sizes of extrusion machines, the new line Green Pipe (green tube), whose concept is in energy saving based on an Efficient Air Cooling (EAC) more efficient cooling system, saving a 25-30% of length of cooling, and a special spiral mandrel called Kryos, that allows to reduce an additional 20% the length of cooling, as well as other subsequent teams that recycle energy.

In the Division of construction (profile extrusion), battenfeld-cincinnati will show a full range of extrusion machines for profile (from 100 to 1,000 kg/h), increased by 25% over previous capabilities thanks to the more powerful engines of 4-axis and the increase of the length of the spindles to 34 diameters for PVC. Also, it will show the latest trends and developments in the manufacture of WPC lines, of which battenfeld-cincinnati has more than 200 lines installed.

INOEX revolutionize again market with 3 updates on teams that already had in portfolio and an important novelty for bathtubs and calibration for vacuum and bathtubs and cooling pipe extrusion lines.

As the familiar system of calibration Advantage, Inoex will expose the new Advantage 1000, for a range of diameters from 400 to 1,000 mm (630-1000 mm standard), with rapid change, central drive, automatic adaptation of nebulisers of cooling and a new stand for the tube. The new Aurex-m has been modified to turn it into a system easier to use, more secure yet and with reduced lead times. INOEX also displays the Pexlink system, with oven for tubes up to 32 mm horizontal and vertical for tubes up to 250 mm in diameter (new Pexlink 250).

Finally, Inoex will launch its innovative vacuum tank to the market during the K and cooling model Advantage 1000 IVT, which incorporates a modular design (giving access to the interior) and a completely new concept of vacuum, with cooling, while maintaining its philosophy based on the realization of rapid changes in diameterease of use and of maintenance, including the possibility of repair of defective parts without stopping production.

The Canadian manufacturer of corrugated and subsequent equipment (sierra, punch...) for plastic tubes Corma will have stand samples of products made with its machinery, which stands out for its high performance, reduction of space required and excellent value for money.

Sciteq, Danish manufacturer of on-line and off-line quality control teams, will be exhibiting at stand the latest version of the X-Act Twin Eye, only system in the world that measures online 360 degrees of the multilayered with soul of aluminium pipes, and measure the outside diameter, the internal, total wall thickness, the thickness of each layer and the ovalación.

With reference to the laboratory equipment, Sciteq will present the new series 2 pressure teams known for its modular system and to which you install the new S40 control system, replacing the current S12. It will also expose the MFI-450 for the measurement of the rate of flow (MFI) and at the same time the rate of flow volume (MVR), thus determining density in hot much more accurately.

Finally, the clients that visit the stand will see elongation, SXW Tensile resistance test equipment tester, ideal for tensile and compression testing up to 100 kN to meet a very wide range of standards such as ISO 178ISO 527, ISO 6259, ISO 9969, ASTM D638 and ASTM D790.

Maris S.p.A. will be the K 2010 three of its representative machines in its wide range of equipment, always seeking the most appropriate solution for the implementation of its customers and a proven and very successful experience in the processing of materials with very different characteristics.

The TM20Hi-Tech for laboratory applications but allowing process very different formulations due to its engine of 15kw of high torque, its port for liquid and the possibility of adapting up 2 lateral feeders.

The already known TM58MW/48D of high volume and the TM72HS/48D in the new series of volume and torque increase with respect to the above but still existing series HT, both extruders of 48 diameters.

Mixaco highlight in this edition of the K in Düsseldorf by the large number of new features that will present, starting with the container mixer model CM-MT (Multitool), which allows mixtures with high level of intensity without increasing the temperature of the material (almost 1 ° C) to mixthus enabling to perform mixes of high sensitivity to temperature as polyolefins with high concentration of organic, black pigment of smoke...

On the other hand, will be also presented the Speedy SD (rapid mixing of material directly in bag and drum, the CM3D, and the cold mixer without blades mixture, thereby reducing the time of cleaning up to be almost negligible.)

Automatik Plastics Machinery GmbH, specializing in pelletising teams, will present both equipment and replacement of the same parties, focusing on five main applications in comprehensive growth markets currently such as CC-PET, recycled PET, microgranceado, biopolymers and thermoplastic fiber-reinforced.

In addition to these well-known products, will be presented two important developments: the new centrifugal dryer Centre for microgranceado and the new system of cooling and drying of laces on conveyor (cutting dry), known as EBG, the cutter will have built-in model cousin Plus 200 of this manufacturer.

The company battenfeld-cincinnati be exhibiting at the 2010 K sheet extrusion lines for PO, PS and PET more important within its newly released Division of "Packaging" (and packaging). Amongst these lines there are new models of extrusion machines for direct PET (without precristalización), based on a single extruder with an intermediate zone of planetary spindles, and the extrusion machines of 75 mm in diameter for high speed with capacity of 2,000 kg/h in polyolefins (PP/PE) and poliestirénicos which can be obtained.

Also, battenfeld-cincinnati also inform attendees on their lines of PVC processing by extrusion machines of planetary spindles.

The good reputation of this manufacturer of rollers of roller press and cooled precedes Van Baal, who will be exhibiting at stand 20 samples of some of the finishes that can offer its customers of sheet extrusion. It will show the system of roller of internal auto-accionamiento, an automatic system for the cleaning of the roller and will provide general information on analysis of cooling for extrusion processes.

SBI, Solutions by Innovations, will show his new developments in non-radioactive thickness gages for plastic sheets (with details of up to 1 micron) as well as their flat heads of extrusion, stressing that incorporates the Frad, consisting of the possibility of change of automatic thickness of higher rank in the market stand.

Historic Cattorini snc will present at the fair in Düsseldorf its latest technology in systems of winding for films and plastic sheets, specifically its fully automatic due to film. Cattorini is noted for its wide range of solutions for the winding (by stations, type revolver, type drum, etc...), rewind, and flipped coils of plastic solutions that it has been offering to manufacturers of former teams (extrusion lines) and end-users since 1974.

Gabler Thermoform will share stand with its American sister company Lyle Industries. As a novelty, and part of his recently presented Focus series of thermoforming stations (formed, cutting and stacking), Gabler will launch to the market the new M60, of formed and cut in the mold of swing arm type and with an area of formed of 500x320mmto complete the range of termoformadoras tilt mold (type "M") that has featured so far the M98 (with an area of formed of 800x550mm, with the possibility of installing a mold of 70 cavities and a production of 120,000 vessels each time).

The new teams are still maintaining the characteristics of robustness, speed, reliability, flexibility and compatibility to include them on other manufacturers.

Austrian manufacturer of moulds for the thermoforming and injection of technical products, as well as tailor-made solutions for the removal of the mold, stacking, automatic cash, bagging and packing of thermoformed products will have a corporate booth in Hall 12, booth E49/2 and in Hall 3, stand G29, together with a manufacturer of termoformadoras, where you can see up the new Pick-up Stacker (unit of extraction of the mold and stacking) semi-automatic.

The new system for the recycling of PVC/PE/PP tubes up to 1,200 mm in diameter and 6 m in length (the system more economical and secure for the pre-triturado of these products), the crusher mill type SM 1000 / 1200-S7-3 designed for crushing of a multitude of materials, the new mill SMV 800/1200-sp9 release notes-3, with feed rollers forced BOP/BOPET films, for example, and the sprayer model ZM800, the largest of his series with a capacity of spray / material micronizar crushed with a capacity of up to 1,200 kg/hthey are the most important developments presented Neue Herbold at this event.

Schwing, known company that provides cleaning equipment for temperature to extract the polymer pollutant of the various tools for the transformation of plastics such as injection nozzles, packs of spinning, extrusion heads and plates punched for the pelletising of plastics, among other applications, it will show visitors the before and after several pieces of those already mentioned above and some others.

At the same time, Schwing will keep the doors of your company in Neukirchen-Vluyn open, for those customers who want to see the various processes of cleaning in situ, as it has a laboratory with cleaning systems by Chamber of gas (Compactclean and Maxiclean)temperature and vacuum controlled simultaneously (Vacuclean) and fluidized bed (Innovaclean), these last two pirolíticos. Attendees can see the high efficiency, safety and non-existent environmental pollution with that carried out the cleaning equipment.

Corema International held his coming-out following the demise of the old Corema S.p.A., with new NPC/C series, which will expose the 50 and 150 models. In this new series, customers can see various advantages with regard to the above and still in program teams of cooling water by condensation of air. Corema International will inform visitors about the extensive offer to the systems of cooling water (Chiller), air (Modulair), forced evaporation (Thermo Chiller) and for restraint of water and oil (Termotrol).